A magnetic centrifugal pump (hereinafter referred to as a magnetic pump) usually consists of an electric motor, a magnetic coupling and a corrosion-resistant centrifugal pump. Its main feature is the use of a magnetic coupling to transmit power in a completely leak-free manner.
A magnetic centrifugal pump (hereinafter referred to as a magnetic pump) usually consists of an electric motor, a magnetic coupling and a corrosion-resistant centrifugal pump. Its main feature is the use of a magnetic coupling to transmit power in a completely leak-free manner. When the motor rotates the outer magnet of the magnetic coupling, magnetic force lines pass through the gap and the protective sleeve, acting on the inner magnet, causing the pump rotor to rotate synchronously with the motor and transmit torque without mechanical contact. At the inlet end of the pump shaft, since the fluid is contained in a stationary protective sleeve and there is no dynamic seal, the pump operates safely and without leakage. Pump flow components can be made of corrosion resistant materials such as 304, 304L, 302, 321, 316, 316L, UB6, CD4MCU, titanium alloys, nickel alloys, etc. depending on requirements. IMC series magnetic pump is a new type of fully sealed and corrosion-resistant pump developed by the national level joint magnetic pump design team. Its technical and economic indicators are comparable to foreign analogues of the late 1980s. The types and main parameters of the RMC series magnetic pump comply with the requirements of the TB/T7742-95 standard “Small centrifugal pumps with magnetic drive”.
RMC series magnetic pump is suitable for industries such as petroleum, chemical, pharmaceutical, metallurgy, electroplating, environmental protection, food processing, film printing, water treatment, defense industry, etc. It is an ideal equipment for pumping flammable, explosive, volatile, toxic, rare and valuable liquids, as well as various corrosion-resistant liquids.
◆ Maximum operating pressure when pumping: 1.6 MPa
◆Maximum temperature: 100°C
◆ Maximum density: 184 × 10³ kg/m³
◆ Maximum viscosity: 30 × 10⁻⁶ m²/s (liquid without solid particles and fibers). If the system operating pressure exceeds 1.6MPa, special design can be made, and the maximum system operating pressure can reach 15MPa.
When the specific gravity and viscosity of the pumped liquid is high, the shaft power increases, so it is necessary to use an electric motor that matches the shaft power.
The static seal between the suction section, middle section and discharge section of the pump is made of metal seal and double O-ring seal, and the pump shaft seal uses high-performance hemp packing or mechanical seal, which is safe and reliable.
This pump can operate without water, is not subject to rapid wear, is easy to assemble and maintain, and has a long service life.
The simple modular dosing unit is a complete plug-and-play dosing device. It is designed, manufactured, assembled and tested at the manufacturing plant in accordance with the customer's technological requirements, and then completely delivered to the site.
CAD technology is used to redesign the design multiple times to ensure that the submersible pump body and impeller are perfectly matched, allowing fibers and debris to pass through easily without becoming tangled or clogged.
DN25–DN1200; PN16–PN160, Class150–Class900; cryogenic steel LF3, stainless steel; t=-196℃…+120℃, extended rod, flanged and welded connection.
Can pump clean water and slightly contaminated water with temperatures up to 40°C and pH 4–10; the maximum diameter of passing particles is 100 mm.
An automated system of equipment for accurately dosing certain chemical reagents into the water being treated (“source water”). The main task is “accurate, continuous, automatic” dosing of reagents, replacing the unstable and ineffective manual method.
The RUB Corrosion and Wear Resistant Slurry Pump is a cantilever, single stage, single stroke centrifugal pump specifically designed for pumping corrosive media containing fine solids.
Technical parameters: capacity up to 300 m³/h, pressure up to 48 bar
The fluoroplastic FOB magnetic pump is a chemical process pump that uses the principle of modern magnetic mechanics and transfers force non-contactly using permanent magnets. As the motor rotates, the outer rotor (outer magnetic system) drives magnetic lines of force that pass through the thermowell and cause the inner rotor (inner magnetic system) and impeller to rotate synchronously.
DN15–DN800; PN16–PN100, Class150–Class600; cryogenic steels LF2, 304,316; operating temperature -196℃…+80℃; extended anti-freeze rod, flanged/welded connection.
The FZX series PTFE self-priming pump is designed and manufactured in accordance with international standards and based on non-metallic pump manufacturing technology. The pump body is made in the form of a metal shell lined with fluoroplastic, and all flow components are made of fluoroplastic alloy.
DN50–DN2600; PN10–PN63, Class150; cryogenic stainless steel body, special seal for low temperatures; t=-196℃…+60℃, extended rod, wafer and flange versions.
Technical parameters: minimum flow rate up to 0.03 l/min, pressure up to 24 bar
Diameter: DN15–DN1200; Pressure: PN16–PN160, Class150–Class2500; Housing material: WCB, stainless steel 304/316, duplex steel; Connection: flange, threaded, welded, clamp; Drive: manual, pneumatic, electric, hydraulic.
DN25–DN2000; PN10–PN420, Class150–Class2500; Housing: carbon steel, stainless steel, cast iron; Connection: flange, welding; Drive: flywheel, electric drive, pneumatic drive.
